Tile calculator and tiling cost per m² (Australia)

Enter the room size or the area in m², your tile size and the laying pattern. The calculator adds the right wastage, counts tiles and 20 kg adhesive bags, and estimates the tiler’s labour from published per-m² rates for your city.

Prices in AUD, metric units. Last reviewed 14 November 2026.

Advertisement
Advertisement
Advertisement

How much extra tile to buy

Retailers recommend about 10% extra for a straight lay, 15% for a diagonal lay and 20–25% for herringbone, because of cuts and breakages. Keep a few spare tiles from the same batch for future repairs; colour can vary between batches.

Adhesive coverage depends on the product and the notch size. Davco Ultraflex covers about 12 m² per 20 kg bag with a 6 mm notch; Davco Powder Mastic about 7 m² with a 10 mm notch; Dunlop Tiler’s Mastic about 10 m² at 6 mm and 6 m² at 10 mm (manufacturer data sheets). The calculator uses about 10 m² per bag for walls (6 mm notch) and 6.5 m² for floors (10 mm notch).

Advertisement

Standards and licences for tiling

AS 3958:2023 Installation of ceramic and stone tiles (with Amendment 1:2024) replaced AS 3958.1-2007. According to HIA it is not a primary NCC reference, so it applies when your contract calls it up. In wet areas, waterproofing under the tiles must meet NCC Housing Provisions Part 10.2 and AS 3740:2021.

In Victoria, tiling-only work does not need builder registration (Consumer Affairs Victoria). In NSW and Queensland the general value thresholds apply ($5,000 incl. GST in NSW, $3,300 in QLD), so check the tiler’s licence on larger jobs.

Tiler rates in Australia (AUD per m², installation)

ItemPrice (AUD)SourceDate
Floor tile installation, national$44 low / $72 median / $101 high per m²Airtasker17 Mar 2025
Sydney average$95 per m²Airtasker17 Mar 2025
Melbourne average$66 per m²Airtasker17 Mar 2025
Brisbane average$63 per m²Airtasker17 Mar 2025
Perth average$65 per m²Airtasker17 Mar 2025
Adelaide average$62 per m²Airtasker17 Mar 2025
Tiler hourly rateSydney up to $50/h; Adelaide about $45/hAirtasker17 Mar 2025

These are indicative ranges from the named sources on the dates shown, not quotes. Prices vary with site access, finishes and season; get at least three written quotes. Licensing thresholds differ by state: in NSW a licence and a written contract are needed for residential building work over $5,000 incl. GST (NSW Government, Guide to providing home building contracts, updated 11 Jun 2026); in Queensland a QBCC licence is needed for building work valued over $3,300 (QBCC, When you need a licence); in Victoria builder registration applies to domestic building work over $10,000, with single-trade work such as tiling, painting, plumbing or electrical exempt from builder registration (Consumer Affairs Victoria, updated 12 Dec 2025). Plumbing, gas and electrical work always needs a licensed tradie.

Frequently asked questions

How much do tilers charge per m² in Australia?

About $72 per m² median for floor tile installation, from about $62 in Adelaide to $95 in Sydney (Airtasker, Mar 2025). Supply of tiles is extra.

How many extra tiles should I buy?

About 10% for a straight lay and 15% for a diagonal lay; herringbone needs 20–25% (retailer guidance).

How much tile adhesive do I need per m²?

A 20 kg bag covers roughly 6–12 m², depending on product and notch size; for example Davco Ultraflex about 12 m² with a 6 mm notch (manufacturer data sheet).

Which Australian Standard covers tiling?

AS 3958:2023 Installation of ceramic and stone tiles, which replaced AS 3958.1-2007.

Does a tiler need a licence?

In Victoria tiling-only work is exempt from builder registration. In NSW and Queensland the value thresholds apply, so check the licence for jobs above them.

Other Australian calculators

Sources

Advertisement