Concrete calculator: m³, 20 kg bags and cost (Australia)

Enter your slab, strip footing or post holes in metres and millimetres. You get the volume to order, the number of 20 kg bags if you mix it yourself, an indicative ready-mix price in AUD and the short-load fee your supplier is likely to charge on a small pour.

Prices in AUD, metric units. Last reviewed 14 November 2026.

Advertisement
Advertisement
Advertisement

Ready-mix or bags?

One cubic metre takes about 108–110 bags of 20 kg premix (Boral and Cement Australia figures), so bags only make sense for post holes, small pads and repairs. From about half a cubic metre up, a ready-mix "short load" is usually cheaper and gives you consistent concrete, even after the short-load fee.

Suppliers charge a minimum cartage (short-load) fee on the undelivered part of a load under 4 m³. Holcim schedules (ex-GST) list $70 per undelivered m³ in Sydney Metro, $80 in Melbourne Metro, $90 in Queensland and $50 in Perth Metro. A 2 m³ Sydney pour therefore carries about $140 + GST in short-load fees.

Advertisement

Slab strength, thickness and cover

For housing, the NCC 2022 ABCB Housing Provisions require concrete of not less than 20 MPa at 28 days, i.e. N20 (4.2.10). Your engineer may specify N25 or N32 for exposure or reactive sites. Under a slab on ground, a 0.2 mm polyethylene vapour barrier is required (4.2.8).

Minimum concrete cover to reinforcement is 40 mm to unprotected ground, 30 mm to a membrane in contact with the ground, 20 mm to an internal surface and 40 mm to external exposure (4.2.11). Site classes A, S, M, H, E and P set the footing design; H, E and P sites are designed to AS 2870.

100 mm is the common thickness for a residential slab or driveway and 75 mm for paths; treat these as typical examples, not code minimums. Add about 5% for waste and uneven ground on slabs, and 10% for footings dug in uneven ground (brikbeam guidance; there is no code figure).

Indicative concrete prices and fees in Australia (AUD)

ItemPrice (AUD)SourceDate
Ready-mix N20 (20 MPa), per m³$180 – $220newlifeinaus.com.au (indicative)2026
Ready-mix N25, per m³$210 – $250newlifeinaus.com.au (indicative)2026
Ready-mix N32, per m³$250 – $300newlifeinaus.com.au (indicative)2026
N20 by city, per m³Melbourne $170–210; Sydney $185–230; Brisbane $180–225; Perth $200–280newlifeinaus.com.au (indicative)2026
Plain slab installed, per m²$65 – $85 (labour $20–55/m²)Airtasker7 Nov 2026
Short-load fee, Sydney Metro (load < 4 m³)$70 per undelivered m³ + $2.00/m³ levy, ex-GSTHolcim fee schedule1 Jul 2025
Short-load fee, Melbourne Metro$80 per undelivered m³ + $2.80/m³ levy, ex-GSTHolcim fee schedule1 May 2026
Short-load fee, Queensland$90 per undelivered m³ + $2.50/m³ levy, ex-GSTHolcim fee schedule1 Jan 2026
Short-load fee, Perth Metro$50 per undelivered m³ + $2.00/m³ levy, ex-GSTHolcim fee schedule1 May 2026

These are indicative ranges from the named sources on the dates shown, not quotes. Prices vary with site access, finishes and season; get at least three written quotes. Licensing thresholds differ by state: in NSW a licence and a written contract are needed for residential building work over $5,000 incl. GST (NSW Government, Guide to providing home building contracts, updated 11 Jun 2026); in Queensland a QBCC licence is needed for building work valued over $3,300 (QBCC, When you need a licence); in Victoria builder registration applies to domestic building work over $10,000, with single-trade work such as tiling, painting, plumbing or electrical exempt from builder registration (Consumer Affairs Victoria, updated 12 Dec 2025). Plumbing, gas and electrical work always needs a licensed tradie.

Frequently asked questions

How much concrete do I need for a 3 × 3 m slab?

3 × 3 × 0.10 m = 0.9 m³, or about 0.95 m³ with 5% waste. That is about 104 bags of 20 kg at 110 bags per m³; ready-mix is usually better value at this size even with a short-load fee.

How much is concrete per m³ in Australia?

Indicatively $180–$220 per m³ for N20 and $250–$300 for N32 before delivery fees (newlifeinaus, 2026). Get quotes from local suppliers such as Boral, Holcim, Hanson or Hymix.

What is a short-load fee?

A charge on the undelivered part of a load under 4 m³: for example $70 per m³ in Sydney Metro and $90 per m³ in Queensland (Holcim schedules 2025–26, ex-GST).

What strength concrete do I need for a house slab?

At least N20 (20 MPa at 28 days) under NCC 2022 Housing Provisions 4.2.10. Your engineer may specify N25 or N32 for exposure or reactive soil.

How many 20 kg bags make 1 m³?

About 108–110 bags, based on Boral and Cement Australia figures. This calculator uses 110 to stay on the safe side.

Other Australian calculators

Sources

Advertisement